smilint output for ./ADSL2-LINE-TC-MIB
| Message Severities |
|---|
| Severity | Count |
|---|
| change recommended | 1 |
| warning | 24 |
| Message Types |
|---|
| Type | Count |
|---|
| module-identity-registration (change recommended) | 1 |
| node-implicit (warning) | 1 |
| type-unref (warning) | 23 |
Messages:
ADSL2-LINE-TC-MIB
1: -- extracted from rfc4706.txt
2: -- at Wed Nov 29 06:07:30 2006
13:
14: adsl2TCMIB MODULE-IDENTITY
14: change recommended -
warning: uncontrolled MODULE-IDENTITY registration
15: LAST-UPDATED "200610040000Z" -- October 4th, 2006
16: ORGANIZATION "ADSLMIB Working Group"
17: CONTACT-INFO "WG-email: adslmib@ietf.org
18: Info: https://www1.ietf.org/mailman/listinfo/adslmib
19:
20: Chair: Mike Sneed
21: Sand Channel Systems
22: Postal: P.O. Box 37324
23: Raleigh NC 27627-732
24: Email: sneedmike@hotmail.com
25: Phone: +1 206 600 7022
26:
27: Co-Chair & Co-editor:
28: Menachem Dodge
29: ECI Telecom Ltd.
30: Postal: 30 Hasivim St.
31: Petach Tikva 49517,
32: Israel.
33: Email: mbdodge@ieee.org
34: Phone: +972 3 926 8421
35: Co-editor: Moti Morgenstern
36: ECI Telecom Ltd.
37: Postal: 30 Hasivim St.
38: Petach Tikva 49517,
39: Israel.
40: Email: moti.morgenstern@ecitele.com
41: Phone: +972 3 926 6258
42:
43: Co-editor: Scott Baillie
44: NEC Australia
45: Postal: 649-655 Springvale Road,
46: Mulgrave, Victoria 3170,
47: Australia.
48: Email: scott.baillie@nec.com.au
49: Phone: +61 3 9264 3986
50:
51: Co-editor: Umberto Bonollo
52: NEC Australia
53: Postal: 649-655 Springvale Road,
54: Mulgrave, Victoria 3170,
55: Australia.
56: Email: umberto.bonollo@nec.com.au
57: Phone: +61 3 9264 3385
58: "
59: DESCRIPTION
60: "This MIB Module provides Textual Conventions to be
61: used by the ADSL2-LINE-MIB module for the purpose of
62: managing ADSL, ADSL2, and ADSL2+ lines.
63:
64: Copyright (C) The Internet Society (2006). This version of
65: this MIB module is part of RFC 4706: see the RFC itself for
66: full legal notices."
67:
68: REVISION "200610040000Z" -- October 4th, 2006
69: DESCRIPTION "Initial version, published as RFC 4706."
70: ::= { transmission 238 2 } -- adsl2MIB 2
70: warning -
warning: implicit node definition
71:
72: ------------------------------------------------
73: -- Textual Conventions --
74: ------------------------------------------------
75:
76: Adsl2Unit ::= TEXTUAL-CONVENTION
76: warning -
warning: current type `Adsl2Unit' is not referenced in this module
77: STATUS current
78: DESCRIPTION
79: "Identifies a transceiver as being either an ATU-C or
80: an ATU-R. An ADSL line consists of two transceivers, an ATU-C
81: and an ATU-R. Attributes with this syntax reference the two
82: sides of a line. Specified as an INTEGER, the two values
83: are:
84:
85: atuc(1) -- Central office ADSL terminal unit (ATU-C).
86: atur(2) -- Remote ADSL terminal unit (ATU-R)."
87: SYNTAX INTEGER {
88: atuc(1),
89: atur(2)
90: }
91:
92: Adsl2Direction ::= TEXTUAL-CONVENTION
92: warning -
warning: current type `Adsl2Direction' is not referenced in this module
93: STATUS current
94: DESCRIPTION
95: "Identifies the direction of a band as being
96: either upstream or downstream. Specified as an INTEGER,
97: the two values are:
98: upstream(1), and
99: downstream(2)."
100: SYNTAX INTEGER {
101: upstream(1),
102: downstream(2)
103: }
104:
105:
106:
107: Adsl2TransmissionModeType ::= TEXTUAL-CONVENTION
107: warning -
warning: current type `Adsl2TransmissionModeType' is not referenced in this module
108: STATUS current
109: DESCRIPTION
110: "A set of ADSL2 line transmission modes, with one bit
111: per mode. The notes (F) and (L) denote Full-Rate
112: and Lite/splitterless, respectively:
113: Bit 00 : Regional Std. (ANSI T1.413) (F)
114: Bit 01 : Regional Std. (ETSI DTS/TM06006) (F)
115: Bit 02 : G.992.1 POTS non-overlapped (F)
116: Bit 03 : G.992.1 POTS overlapped (F)
117: Bit 04 : G.992.1 ISDN non-overlapped (F)
118: Bit 05 : G.992.1 ISDN overlapped (F)
119: Bit 06 : G.992.1 TCM-ISDN non-overlapped (F)
120: Bit 07 : G.992.1 TCM-ISDN overlapped (F)
121: Bit 08 : G.992.2 POTS non-overlapped (L)
122: Bit 09 : G.992.2 POTS overlapped (L)
123: Bit 10 : G.992.2 with TCM-ISDN non-overlapped (L)
124: Bit 11 : G.992.2 with TCM-ISDN overlapped (L)
125: Bit 12 : G.992.1 TCM-ISDN symmetric (F) -- not in G.997.1
126: Bit 13-17: Reserved
127: Bit 18 : G.992.3 POTS non-overlapped (F)
128: Bit 19 : G.992.3 POTS overlapped (F)
129: Bit 20 : G.992.3 ISDN non-overlapped (F)
130: Bit 21 : G.992.3 ISDN overlapped (F)
131: Bit 22-23: Reserved
132: Bit 24 : G.992.4 POTS non-overlapped (L)
133: Bit 25 : G.992.4 POTS overlapped (L)
134: Bit 26-27: Reserved
135: Bit 28 : G.992.3 Annex I All-Digital non-overlapped (F)
136: Bit 29 : G.992.3 Annex I All-Digital overlapped (F)
137: Bit 30 : G.992.3 Annex J All-Digital non-overlapped (F)
138: Bit 31 : G.992.3 Annex J All-Digital overlapped (F)
139: Bit 32 : G.992.4 Annex I All-Digital non-overlapped (L)
140: Bit 33 : G.992.4 Annex I All-Digital overlapped (L)
141: Bit 34 : G.992.3 Annex L POTS non-overlapped, mode 1,
142: wide U/S (F)
143: Bit 35 : G.992.3 Annex L POTS non-overlapped, mode 2,
144: narrow U/S(F)
145: Bit 36 : G.992.3 Annex L POTS overlapped, mode 3,
146: wide U/S (F)
147: Bit 37 : G.992.3 Annex L POTS overlapped, mode 4,
148: narrow U/S (F)
149: Bit 38 : G.992.3 Annex M POTS non-overlapped (F)
150: Bit 39 : G.992.3 Annex M POTS overlapped (F)
151: Bit 40 : G.992.5 POTS non-overlapped (F)
152: Bit 41 : G.992.5 POTS overlapped (F)
153: Bit 42 : G.992.5 ISDN non-overlapped (F)
154: Bit 43 : G.992.5 ISDN overlapped (F)
155: Bit 44-45: Reserved
156: Bit 46 : G.992.5 Annex I All-Digital non-overlapped (F)
157: Bit 47 : G.992.5 Annex I All-Digital overlapped (F)
158: Bit 48 : G.992.5 Annex J All-Digital non-overlapped (F)
159: Bit 49 : G.992.5 Annex J All-Digital overlapped (F)
160: Bit 50 : G.992.5 Annex M POTS non-overlapped (F)
161: Bit 51 : G.992.5 Annex M POTS overlapped (F)
162: Bit 52-55: Reserved"
163: SYNTAX BITS {
164: ansit1413(0),
165: etsi(1),
166: g9921PotsNonOverlapped(2),
167: g9921PotsOverlapped(3),
168: g9921IsdnNonOverlapped(4),
169: g9921isdnOverlapped(5),
170: g9921tcmIsdnNonOverlapped(6),
171: g9921tcmIsdnOverlapped(7),
172: g9922potsNonOverlapped(8),
173: g9922potsOverlapped(9),
174: g9922tcmIsdnNonOverlapped(10),
175: g9922tcmIsdnOverlapped(11),
176: g9921tcmIsdnSymmetric(12),
177: reserved1(13),
178: reserved2(14),
179: reserved3(15),
180: reserved4(16),
181: reserved5(17),
182: g9923PotsNonOverlapped(18),
183: g9923PotsOverlapped(19),
184: g9923IsdnNonOverlapped(20),
185: g9923isdnOverlapped(21),
186: reserved6(22),
187: reserved7(23),
188: g9924potsNonOverlapped(24),
189: g9924potsOverlapped(25),
190: reserved8(26),
191: reserved9(27),
192: g9923AnnexIAllDigNonOverlapped(28),
193: g9923AnnexIAllDigOverlapped(29),
194: g9923AnnexJAllDigNonOverlapped(30),
195: g9923AnnexJAllDigOverlapped(31),
196: g9924AnnexIAllDigNonOverlapped(32),
197: g9924AnnexIAllDigOverlapped(33),
198: g9923AnnexLMode1NonOverlapped(34),
199: g9923AnnexLMode2NonOverlapped(35),
200: g9923AnnexLMode3Overlapped(36),
201: g9923AnnexLMode4Overlapped(37),
202: g9923AnnexMPotsNonOverlapped(38),
203: g9923AnnexMPotsOverlapped(39),
204: g9925PotsNonOverlapped(40),
205: g9925PotsOverlapped(41),
206: g9925IsdnNonOverlapped(42),
207: g9925isdnOverlapped(43),
208: reserved10(44),
209: reserved11(45),
210: g9925AnnexIAllDigNonOverlapped(46),
211: g9925AnnexIAllDigOverlapped(47),
212: g9925AnnexJAllDigNonOverlapped(48),
213: g9925AnnexJAllDigOverlapped(49),
214: g9925AnnexMPotsNonOverlapped(50),
215: g9925AnnexMPotsOverlapped(51),
216: reserved12(52),
217: reserved13(53),
218: reserved14(54),
219: reserved15(55)
220: }
221:
222: Adsl2RaMode ::= TEXTUAL-CONVENTION
222: warning -
warning: current type `Adsl2RaMode' is not referenced in this module
223: STATUS current
224: DESCRIPTION
225: "Specifies the rate adaptation behavior for the line.
226: The three possible behaviors are:
227: manual(1) - No Rate-Adaptation. The initialization
228: process attempts to synchronize to a
229: specified rate.
230: raInit(2) - Rate-Adaptation during initialization process
231: only, which attempts to synchronize to a rate
232: between minimum and maximum specified values.
233: dynamicRa(3) - Dynamic Rate-Adaptation during initialization
234: process as well as during SHOWTIME."
235: SYNTAX INTEGER {
236: manual(1),
237: raInit(2),
238: dynamicRa(3)
239: }
240:
241: Adsl2InitResult ::= TEXTUAL-CONVENTION
241: warning -
warning: current type `Adsl2InitResult' is not referenced in this module
242: STATUS current
243: DESCRIPTION
244: "Specifies the result of a full initialization attempt; the
245: six possible result values are:
246: noFail(0) - Successful initialization.
247: configError(1) - Configuration failure.
248: configNotFeasible(2) - Configuration details not supported.
249: commFail(3) - Communication failure.
250: noPeerAtu(4) - Peer ATU not detected.
251: otherCause(5) - Other initialization failure reason.
252:
253: The values used are as defined in ITU-T G.997.1,
254: paragraph 7.5.1.3"
255:
256: SYNTAX INTEGER {
257: noFail(0),
258: configError(1),
259: configNotFeasible(2),
260: commFail(3),
261: noPeerAtu(4),
262: otherCause(5)
263: }
264:
265: Adsl2OperationModes ::= TEXTUAL-CONVENTION
265: warning -
warning: current type `Adsl2OperationModes' is not referenced in this module
266: STATUS current
267: DESCRIPTION
268: "The ADSL2 management model specified includes an ADSL Mode
269: attribute that identifies an instance of ADSL Mode-Specific
270: PSD Configuration object in the ADSL Line Profile. The
271: following classes of ADSL operating mode are defined.
272: The notes (F) and (L) denote Full-Rate and Lite/splitterless
273: respectively:
274: +-------+--------------------------------------------------+
275: | Value | ADSL operation mode description |
276: +-------+--------------------------------------------------+
277:
278: 1 - The default/generic PSD configuration. Default
279: configuration will be used when no other matching
280: mode-specific configuration can be found.
281: 2 - ADSL family. The attributes included in the Mode-
282: Specific PSD Configuration are irrelevant for
283: ITU-T G.992.1 and G.992.2 ADSL modes. Hence, it
284: is possible to map those modes to this generic
285: class.
286: 3-7 - Unused. Reserved for future ITU-T specification.
287: 8 - G.992.3 POTS non-overlapped (F)
288: 9 - G.992.3 POTS overlapped (F)
289: 10 - G.992.3 ISDN non-overlapped (F)
290: 11 - G.992.3 ISDN overlapped (F)
291: 12-13 - Unused. Reserved for future ITU-T specification.
292: 14 - G.992.4 POTS non-overlapped (L)
293: 15 - G.992.4 POTS overlapped (L)
294: 16-17 - Unused. Reserved for future ITU-T specification.
295: 18 - G.992.3 Annex I All-Digital non-overlapped (F)
296: 19 - G.992.3 Annex I All-Digital overlapped (F)
297: 20 - G.992.3 Annex J All-Digital non-overlapped (F)
298: 21 - G.992.3 Annex J All-Digital overlapped (F)
299: 22 - G.992.4 Annex I All-Digital non-overlapped (L)
300: 23 - G.992.4 Annex I All-Digital overlapped (L)
301: 24 - G.992.3 Annex L POTS non-overlapped, mode 1,
302: wide U/S (F)
303: 25 - G.992.3 Annex L POTS non-overlapped, mode 2,
304: narrow U/S(F)
305: 26 - G.992.3 Annex L POTS overlapped, mode 3,
306: wide U/S (F)
307: 27 - G.992.3 Annex L POTS overlapped, mode 4,
308: narrow U/S (F)
309: 28 - G.992.3 Annex M POTS non-overlapped (F)
310: 29 - G.992.3 Annex M POTS overlapped (F)
311: 30 - G.992.5 POTS non-overlapped (F)
312: 31 - G.992.5 POTS overlapped (F)
313: 32 - G.992.5 ISDN non-overlapped (F)
314: 33 - G.992.5 ISDN overlapped (F)
315: 34-35 - Unused. Reserved for future ITU-T specification.
316: 36 - G.992.5 Annex I All-Digital non-overlapped (F)
317: 37 - G.992.5 Annex I All-Digital overlapped (F)
318: 38 - G.992.5 Annex J All-Digital non-overlapped (F)
319: 39 - G.992.5 Annex J All-Digital overlapped (F)
320: 40 - G.992.5 Annex M POTS non-overlapped (F)
321: 41 - G.992.5 Annex M POTS overlapped (F)
322:
323: "
324: SYNTAX INTEGER {
325: defMode (1),
326: adsl(2),
327: g9923PotsNonOverlapped(8),
328: g9923PotsOverlapped(9),
329: g9923IsdnNonOverlapped(10),
330: g9923isdnOverlapped(11),
331: g9924potsNonOverlapped(14),
332: g9924potsOverlapped(15),
333: g9923AnnexIAllDigNonOverlapped(18),
334: g9923AnnexIAllDigOverlapped(19),
335: g9923AnnexJAllDigNonOverlapped(20),
336: g9923AnnexJAllDigOverlapped(21),
337: g9924AnnexIAllDigNonOverlapped(22),
338: g9924AnnexIAllDigOverlapped(23),
339: g9923AnnexLMode1NonOverlapped(24),
340: g9923AnnexLMode2NonOverlapped(25),
341: g9923AnnexLMode3Overlapped(26),
342: g9923AnnexLMode4Overlapped(27),
343: g9923AnnexMPotsNonOverlapped(28),
344: g9923AnnexMPotsOverlapped(29),
345: g9925PotsNonOverlapped(30),
346: g9925PotsOverlapped(31),
347: g9925IsdnNonOverlapped(32),
348: g9925isdnOverlapped(33),
349: g9925AnnexIAllDigNonOverlapped(36),
350: g9925AnnexIAllDigOverlapped(37),
351: g9925AnnexJAllDigNonOverlapped(38),
352: g9925AnnexJAllDigOverlapped(39),
353: g9925AnnexMPotsNonOverlapped(40),
354: g9925AnnexMPotsOverlapped(41)
355: }
356:
357:
358: Adsl2PowerMngState ::= TEXTUAL-CONVENTION
358: warning -
warning: current type `Adsl2PowerMngState' is not referenced in this module
359: STATUS current
360: DESCRIPTION
361: "Attributes with this syntax uniquely identify each power
362: management state defined for the ADSL/ADSL2 or ADSL2+ link.
363: The possible values are:
364: l0(1) - L0 - Full power management state.
365: l1(2) - L1 - Low power management state (for G.992.2).
366: l2(3) - L2 - Low power management state (for G.992.3,
367: G.992.4, and G.992.5).
368: l3(4) - L3 - Idle power management state."
369:
370: SYNTAX INTEGER {
371: l0(1),
372: l1(2),
373: l2(3),
374: l3(4)
375: }
376:
377: Adsl2ConfPmsForce ::= TEXTUAL-CONVENTION
377: warning -
warning: current type `Adsl2ConfPmsForce' is not referenced in this module
378: STATUS current
379: DESCRIPTION
380: "Attributes with this syntax are configuration parameters
381: that reference the desired power management state for the
382: ADSL/ADSL2 or ADSL2+ link:
383: l3toL0(0) - Perform a transition from L3 to L0
384: (Full power management state).
385: l0toL2(2) - Perform a transition from L0 to L2
386: (Low power management state).
387: l0orL2toL3(3) - Perform a transition into L3 (Idle
388: power management state).
389:
390: The values used are as defined in ITU-T G.997.1,
391: paragraph 7.3.1.1.3"
392:
393: SYNTAX INTEGER {
394: l3toL0(0),
395: l0toL2(2),
396: l0orL2toL3(3)
397: }
398:
399: Adsl2LConfProfPmMode ::= TEXTUAL-CONVENTION
399: warning -
warning: current type `Adsl2LConfProfPmMode' is not referenced in this module
400: STATUS current
401: DESCRIPTION
402: "Attributes with this syntax are configuration parameters
403: that reference the power modes/states into which the ATU-C or
404: ATU-R may autonomously transit.
405:
406: It is a BITS structure that allows control of the following
407: transit options:
408: allowTransitionsToIdle(0) - XTU may autonomously transit
409: to idle (L3) state.
410: allowTransitionsToLowPower(1) - XTU may autonomously transit
411: to low-power (L2) state."
412:
413: SYNTAX BITS {
414: allowTransitionsToIdle(0),
415: allowTransitionsToLowPower(1)
416: }
417:
418: Adsl2LineLdsf ::= TEXTUAL-CONVENTION
418: warning -
warning: current type `Adsl2LineLdsf' is not referenced in this module
419: STATUS current
420: DESCRIPTION
421: "Attributes with this syntax are configuration parameters
422: that control the Loop Diagnostic mode for the ADSL/ADSL2 or
423: ADSL2+ link. The possible values are:
424: inhibit(0) - Inhibit Loop Diagnostic mode.
425: force(1) - Force/Initiate Loop Diagnostic mode.
426:
427: The values used are as defined in ITU-T G.997.1,
428: paragraph 7.3.1.1.8"
429:
430: SYNTAX INTEGER {
431: inhibit(0),
432: force(1)
433: }
434:
435: Adsl2LdsfResult ::= TEXTUAL-CONVENTION
435: warning -
warning: current type `Adsl2LdsfResult' is not referenced in this module
436: STATUS current
437: DESCRIPTION
438: "Possible failure reasons associated with performing
439: a Dual Ended Loop Test (DELT) on a DSL line.
440: Possible values are:
441: none(1) - The default value in case LDSF was never
442: requested for the associated line.
443: success(2) - The recent command completed
444: successfully.
445: inProgress(3) - The Loop Diagnostics process is in
446: progress.
447: unsupported(4) - The NE or the line card doesn't support
448: LDSF.
449: cannotRun(5) - The NE cannot initiate the command, due
450: to a nonspecific reason.
451: aborted(6) - The Loop Diagnostics process aborted.
452: failed(7) - The Loop Diagnostics process failed.
453: illegalMode(8) - The NE cannot initiate the command, due
454: to the specific mode of the relevant
455: line.
456: adminUp(9) - The NE cannot initiate the command, as
457: the relevant line is administratively
458: 'Up'.
459: tableFull(10) - The NE cannot initiate the command, due
460: to reaching the maximum number of rows
461: in the results table.
462: noResources(11) - The NE cannot initiate the command, due
463: to lack of internal memory resources."
464: SYNTAX INTEGER {
465: none(1),
466: success(2),
467: inProgress(3),
468: unsupported(4),
469: cannotRun(5),
470: aborted(6),
471: failed(7),
472: illegalMode(8),
473: adminUp(9),
474: tableFull(10),
475: noResources(11)
476: }
477:
478: Adsl2SymbolProtection ::= TEXTUAL-CONVENTION
478: warning -
warning: current type `Adsl2SymbolProtection' is not referenced in this module
479: STATUS current
480: DESCRIPTION
481: "Attributes with this syntax are configuration parameters
482: that reference the minimum-length impulse noise protection
483: (INP) in terms of number of symbols. The possible values are:
484: noProtection (i.e., INP not required), halfSymbol (i.e., INP
485: length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol."
486:
487: SYNTAX INTEGER {
488: noProtection(1),
489: halfSymbol(2),
490: singleSymbol(3),
491: twoSymbols(4),
492: threeSymbols(5),
493: fourSymbols(6),
494: fiveSymbols(7),
495: sixSymbols(8),
496: sevenSymbols(9),
497: eightSymbols(10),
498: nineSymbols(11),
499: tenSymbols(12),
500: elevenSymbols(13),
501: twelveSymbols(14),
502: thirteeSymbols(15),
503: fourteenSymbols(16),
504: fifteenSymbols(17),
505: sixteenSymbols(18)
506: }
507: Adsl2MaxBer ::= TEXTUAL-CONVENTION
507: warning -
warning: current type `Adsl2MaxBer' is not referenced in this module
508: STATUS current
509: DESCRIPTION
510: "Attributes with this syntax are configuration parameters
511: that reference the maximum Bit Error Rate (BER).
512: The possible values are:
513:
514: eminus3(1) - Maximum BER=E^-3
515: eminus5(2) - Maximum BER=E^-5
516: eminus7(3) - Maximum BER=E^-7"
517: SYNTAX INTEGER {
518: eminus3(1),
519: eminus5(2),
520: eminus7(3)
521: }
522:
523: Adsl2ScMaskDs ::= TEXTUAL-CONVENTION
523: warning -
warning: current type `Adsl2ScMaskDs' is not referenced in this module
524: STATUS current
525: DESCRIPTION
526: "Each one of the 512 bits in this OCTET
527: STRING array represents the corresponding bin
528: in the downstream direction. A value of one
529: indicates that the bin is not in use."
530: SYNTAX OCTET STRING (SIZE(0..64))
531:
532: Adsl2ScMaskUs ::= TEXTUAL-CONVENTION
532: warning -
warning: current type `Adsl2ScMaskUs' is not referenced in this module
533: STATUS current
534: DESCRIPTION
535: "Each one of the 64 bits in this OCTET
536: STRING array represents the corresponding bin
537: in the upstream direction. A value of one
538: indicates that the bin is not in use."
539: SYNTAX OCTET STRING (SIZE(0..8))
540:
541: Adsl2RfiDs ::= TEXTUAL-CONVENTION
541: warning -
warning: current type `Adsl2RfiDs' is not referenced in this module
542: STATUS current
543: DESCRIPTION
544: "Each one of the 512 bits in this OCTET
545: STRING array represents the corresponding bin
546: in the downstream direction. A value of one
547: indicates that the bin is part of a notch
548: filter."
549: SYNTAX OCTET STRING (SIZE(0..64))
550:
551: Adsl2PsdMaskDs ::= TEXTUAL-CONVENTION
551: warning -
warning: current type `Adsl2PsdMaskDs' is not referenced in this module
552: STATUS current
553: DESCRIPTION
554: "This is a structure that represents up to
555: 32 PSD Mask breakpoints.
556: Each breakpoint occupies 3 octets: The first
557: two octets hold the index of the sub-carrier
558: associated with the breakpoint. The third octet
559: holds the PSD reduction at the breakpoint from 0
560: (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
561: 0.5 dBm/Hz."
562: SYNTAX OCTET STRING (SIZE(0..96))
563:
564: Adsl2PsdMaskUs ::= TEXTUAL-CONVENTION
564: warning -
warning: current type `Adsl2PsdMaskUs' is not referenced in this module
565: STATUS current
566: DESCRIPTION
567: "This is a structure that represents up to
568: 4 PSD Mask breakpoints.
569: Each breakpoint occupies 3 octets: The first
570: two octets hold the index of the sub-carrier
571: associated with the breakpoint. The third octet
572: holds the PSD reduction at the breakpoint from 0
573: (0 dBm/Hz) to 255 (-127.5 dBm/Hz) using units of
574: 0.5 dBm/Hz."
575: SYNTAX OCTET STRING (SIZE(0..12))
576:
577: Adsl2Tssi ::= TEXTUAL-CONVENTION
577: warning -
warning: current type `Adsl2Tssi' is not referenced in this module
578: STATUS current
579: DESCRIPTION
580: "This is a structure that represents up to
581: 32 transmit spectrum shaping (TSSi) breakpoints.
582: Each breakpoint occupies 3 octets: The first
583: two octets hold the index of the sub-carrier
584: associated with the breakpoint. The third octet
585: holds the shaping parameter at the breakpoint. It
586: is a value from 0 to 127 (units of -0.5 dB). The
587: special value 127 indicates that the sub-carrier
588: is not transmitted."
589: SYNTAX OCTET STRING (SIZE(0..96))
590:
591: Adsl2LastTransmittedState ::= TEXTUAL-CONVENTION
591: warning -
warning: current type `Adsl2LastTransmittedState' is not referenced in this module
592: STATUS current
593: DESCRIPTION
594: "This parameter represents the last successfully
595: transmitted initialization state in the last full
596: initialization performed on the line. States are
597: per the specific xDSL technology and are numbered
598: from 0 (if G.994.1 is used) or 1 (if G.994.1 is
599: not used) up to Showtime."
600: SYNTAX INTEGER {
601: atucG9941(0),
602: atucQuiet1(1),
603: atucComb1(2),
604: atucQuiet2(3),
605: atucComb2(4),
606: atucIcomb1(5),
607: atucLineprob(6),
608: atucQuiet3(7),
609: atucComb3(8),
610: atucIComb2(9),
611: atucMsgfmt(10),
612: atucMsgpcb(11),
613: atucQuiet4(12),
614: atucReverb1(13),
615: atucTref1(14),
616: atucReverb2(15),
617: atucEct(16),
618: atucReverb3(17),
619: atucTref2(18),
620: atucReverb4(19),
621: atucSegue1(20),
622: atucMsg1(21),
623: atucReverb5(22),
624: atucSegue2(23),
625: atucMedley(24),
626: atucExchmarker(25),
627: atucMsg2(26),
628: atucReverb6(27),
629: atucSegue3(28),
630: atucParams(29),
631: atucReverb7(30),
632: atucSegue4(31),
633: atucShowtime(32),
634: --
635: aturG9941(100),
636: aturQuiet1(101),
637: aturComb1(102),
638: aturQuiet2(103),
639: aturComb2(104),
640: aturIcomb1(105),
641: aturLineprob(106),
642: aturQuiet3(107),
643: aturComb3(108),
644: aturIcomb2(109),
645: aturMsgfmt(110),
646: aturMsgpcb(111),
647: aturReverb1(112),
648: aturQuiet4(113),
649: aturReverb2(114),
650: aturQuiet5(115),
651: aturReverb3(116),
652: aturEct(117),
653: aturReverb4(118),
654: aturSegue1(119),
655: aturReverb5(120),
656: aturSegue2(121),
657: aturMsg1(122),
658: aturMedley(123),
659: aturExchmarker(124),
660: aturMsg2(125),
661: aturReverb6(126),
662: aturSegue3(127),
663: aturParams(128),
664: aturReverb7(129),
665: aturSegue4(130),
666: aturShowtime(131)
667: }
668:
669: Adsl2LineStatus ::= TEXTUAL-CONVENTION
669: warning -
warning: current type `Adsl2LineStatus' is not referenced in this module
670: STATUS current
671: DESCRIPTION
672: "Attributes with this syntax are status parameters
673: that reflect the failure status for a given endpoint of
674: ADSL/ADSL2 or ADSL2+ link.
675:
676: This BITS structure can report the following failures:
677:
678: noDefect(0) - This bit position positively reports
679: that no defect or failure exists.
680: lossOfFrame(1) - Loss of frame synchronization.
681: lossOfSignal(2) - Loss of signal.
682: lossOfPower(3) - Loss of power. Usually this failure may
683: be reported for ATU-Rs only.
684: initFailure(4) - Recent initialization process failed.
685: Never active on ATU-R."
686:
687: SYNTAX BITS {
688: noDefect(0),
689: lossOfFrame(1),
690: lossOfSignal(2),
691: lossOfPower(3),
692: initFailure(4)
693: }
694:
695: Adsl2ChAtmStatus ::= TEXTUAL-CONVENTION
695: warning -
warning: current type `Adsl2ChAtmStatus' is not referenced in this module
696: STATUS current
697: DESCRIPTION
698: "Attributes with this syntax are status parameters that
699: reflect the failure status for Transmission Convergence (TC)
700: layer of a given ATM interface (data path over an ADSL/ADSL2
701: or ADSL2+ link).
702:
703: This BITS structure can report the following failures:
704: noDefect(0) - This bit position positively
705: reports that no defect or failure
706: exists.
707: noCellDelineation(1) - The link was successfully
708: initialized, but cell delineation
709: was never acquired on the
710: associated ATM data path.
711: lossOfCellDelineation(2) - Loss of cell delineation on the
712: associated ATM data path."
713:
714: SYNTAX BITS {
715: noDefect(0),
716: noCellDelineation(1),
717: lossOfCellDelineation(2)
718: }
719:
720: Adsl2ChPtmStatus ::= TEXTUAL-CONVENTION
720: warning -
warning: current type `Adsl2ChPtmStatus' is not referenced in this module
721: STATUS current
722: DESCRIPTION
723: "Attributes with this syntax are status parameters that
724: reflect the failure status for a given PTM interface (packet
725: data path over an ADSL/ADSL2 or ADSL2+ link).
726:
727: This BITS structure can report the following failures:
728: noDefect(0) - This bit position positively
729: reports that no defect or failure exists.
730: outOfSync(1) - Out of synchronization."
731:
732: SYNTAX BITS {
733: noDefect(0),
734: outOfSync(1)
735: }
736:
737: END
738:
739: --
740: -- Copyright (C) The Internet Society (2006).
741: --
742: -- This document is subject to the rights, licenses and restrictions
743: -- contained in BCP 78, and except as set forth therein, the authors
744: -- retain all their rights.
745: --
746: -- This document and the information contained herein are provided on an
747: -- "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
748: -- OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
749: -- ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
750: -- INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
751: -- INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
752: -- WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
753: --
754: -- Intellectual Property
755: --
756: -- The IETF takes no position regarding the validity or scope of any
757: -- Intellectual Property Rights or other rights that might be claimed to
758: -- pertain to the implementation or use of the technology described in
759: -- this document or the extent to which any license under such rights
760: -- might or might not be available; nor does it represent that it has
761: -- made any independent effort to identify any such rights. Information
762: -- on the procedures with respect to rights in RFC documents can be
763: -- found in BCP 78 and BCP 79.
764: --
765: -- Copies of IPR disclosures made to the IETF Secretariat and any
766: -- assurances of licenses to be made available, or the result of an
767: -- attempt made to obtain a general license or permission for the use of
768: -- such proprietary rights by implementers or users of this
769: -- specification can be obtained from the IETF on-line IPR repository at
770: -- http://www.ietf.org/ipr.
771: --
772: -- The IETF invites any interested party to bring to its attention any
773: -- copyrights, patents or patent applications, or other proprietary
774: -- rights that may cover technology that may be required to implement
775: -- this standard. Please address the information to the IETF at
776: -- ietf-ipr@ietf.org.
777: --
778: